[Virginia Tech Department of Physics]

Revised 07/11/2016

Physics 2306 Laboratory Equipment List

Lab 6: Circuits and Electric Potential

Transition notes:

  1. The following can stay from the previous lab:
    • All three of the black banana cords
    • Both of the red banana cords, you will need to add another one to make a total of 3 for this lab
  2. Sweepy!

Equipment List:

  1. 2306 Circuit Board with:
    • C14 (2.47V) bulb in all three sockets.
    • 2 x D Cell Battery, one in each Battery Holder.
  2. 3 x Red banana plug cord
  3. 3 x Black banana plug cord
  4. 3 x Black alligator clips
  5. 3 x Red alligator clips
  6. Telegraph Switch
  7. 2 x Autorange Multimeter
  8. Current Limited Power Supply
  9. "Bento Box" Filled with:
    • Items needed for this lab:
      • Manual Pencil Sharpener
      • Pack of Colored Pencils
        • 2 x Black Colored Pencil.
        • 2 x Brown Colored Pencil.
        • 2 x Red Colored Pencil.
        • 2 x Orange Colored Pencil.
        • 2 x Yellow Colored Pencil.
        • 2 x Green Colored Pencil.
        • 2 x Blue Colored Pencil.
        • 2 x Purple Colored Pencil.
      • 5 x Light Element
      • 2 x sets of Long Jumper Cables
        • 2 x Long Black Pin Jumper.
        • 2 x Long Brown Pin Jumper.
        • 2 x Long Red Pin Jumper.
        • 2 x Long Orange Pin Jumper.
        • 2 x Long Yellow Pin Jumper.
        • 2 x Long Green Pin Jumper.
        • 2 x Long Blue Pin Jumper.
        • 2 x Long Purple Pin Jumper.
        • 2 x Long Gray Pin Jumper.
        • 2 x Long White Pin Jumper.
      • 2 x sets of Short Jumper Cables
        • 2 x Short Black Pin Jumper.
        • 2 x Short Brown Pin Jumper.
        • 2 x Short Red Pin Jumper.
        • 2 x Short Orange Pin Jumper.
        • 2 x Short Yellow Pin Jumper.
        • 2 x Short Green Pin Jumper.
        • 2 x Short Blue Pin Jumper.
        • 2 x Short Purple Pin Jumper.
        • 2 x Short Gray Pin Jumper.
        • 2 x Short White Pin Jumper.
      • 2 x sets of Jumper Cable Extentions
        • 2 x Black Pin Jumper Extension.
        • 2 x Brown Pin Jumper Extension.
        • 2 x Red Pin Jumper Extension.
        • 2 x Orange Pin Jumper Extension.
        • 2 x Yellow Pin Jumper Extension.
        • 2 x Green Pin Jumper Extension.
        • 2 x Blue Pin Jumper Extension.
        • 2 x Purple Pin Jumper Extension.
        • 2 x Gray Pin Jumper Extension.
        • 2 x Long White Pin Jumper Extension.
    • Items in the bento box for other labs
      • Collection of resistors
        • 5 x 4.7 ohm resistors
        • 5 x 10 ohm resistors
        • 5 x 50 ohm resistors
        • 2 x 100 ohm resistors
        • 2 x 560 ohm resistors
        • 5 x 10 kohm resistors
        • 2 x 100 kohm resistors
      • Collection of Capcitors
        • 5 x 1 μF Capacitor
        • 2 x 100 μF Capacitor
The whole table setup. From left to right on the main table there is A closed bentobox full of supplies. Next there are two Multimeters next to eachother. Futher in from top to bottom is te current limited power supply, the banana plug wires and alligator adaptors organized neatly by coiling the wires around the adaptors in a large circle. Finally the pasco circuit board is at the bottom. The rest of the table has the normal equipment that stays at all times.

This is what your table should look like once set up

Additional Images below:

One of the component bento boxes open with all of the items organized inside.

A correctly packed Bento box

A close up image of the lab specific items.

The items not in the bento box.

The items to be put out that do not go in the bento box

Items that don't belong in the bento box